24/7 on call

When an air conditioner is not turning on, the cause is often simple: flat batteries in the remote, a tripped breaker or switched-off isolator, the wrong mode selected, a timer still active, or a safety function after a power cut. Start by checking the remote, the power supply and the display for error codes. If the indoor unit runs but the outdoor unit does not, or an error code appears, note it and call a technician. Do not open covers or electrical panels yourself, and do not try to work on the refrigerant circuit, which in Switzerland requires a special authorisation.

Air conditioner not turning on: step-by-step checks

  1. Remote control: replace the batteries; check the display shows the right mode (cooling, not fan or heating).
  2. Power: check the breaker in the fuse box and any isolator switch near the outdoor unit.
  3. Timers: deactivate any on/off timer or weekly schedule.
  4. Set temperature: make sure it is below the room temperature in cooling mode.
  5. Wait: after switching on, many units wait a few minutes before starting the compressor.
  6. Error code: note any blinking lights or codes on the display.

Common causes

Symptom Possible cause
No reaction at all Remote batteries, power, breaker
Indoor unit starts, no cooling Wrong mode, outdoor unit not starting, protection active
Starts then stops Protection, dirty filter, error
Blinking lights Error code; see the manual
Breaker trips again Electrical fault; call a technician

After a power cut or thunderstorm

Summer thunderstorms are common in Ticino. After a power cut, some units need a manual restart, and surges can trip breakers or damage electronics. If the manual allows it, switch the unit off at its isolator or breaker for a few minutes, then back on, provided the switch is dry and safely reachable. If a breaker trips again, do not reset it: have the unit checked. A surge protector can help prevent damage.

The first start of the season

Units that have not run since autumn may need a little attention. Clean the filters before the first start; see how often to clean air conditioner filters. Check that the outdoor unit is free of leaves and that nothing blocks the condensate drain. Ideally, schedule maintenance in spring, before the first heat wave, when technicians have more availability.

Error codes

Most units show an error code or a sequence of blinking lights. The manual explains the meaning; if you do not have it, the manufacturer’s website often does. Common codes point to sensor faults, communication errors between indoor and outdoor units, high or low pressure, or condensate problems. Do not reset repeatedly; note the code and tell the technician.

When to stop and call a technician

  • The breaker trips again after resetting.
  • There is a burning smell or visible damage.
  • Water is leaking from the indoor unit.
  • The outdoor unit makes unusual noises or does not start.
  • An error code reappears.

Prevention

Regular maintenance reduces breakdowns: cleaning filters and coils, checking the condensate drain, testing electrical connections and checking operating pressures. Many problems that appear on the first hot day could be spotted during a spring service. Units that short cycle are also more prone to faults; see air conditioner short cycling.

Example: apartment in Locarno

On the first hot day in June, the air conditioner does not respond. The owner replaces the remote batteries without success. The breaker is on. The display shows a blinking code, which the manual identifies as a communication error. A technician finds a loose connection in the outdoor unit after a winter storm, repairs it and services the unit at the same time.

Water from the indoor unit

Sometimes the unit runs but stops after a while because the condensate drain is blocked. Many units have a float switch that stops cooling when water builds up, to protect the room from leaks. If you see water dripping from the indoor unit or a damp patch on the wall below, switch the unit off and call a technician. The drain line needs to be cleared, and the cause, often dust and biofilm, should be removed. Regular servicing prevents this.

Information for the technician

  • Brand and model of the indoor and outdoor units.
  • Any error code or blinking pattern.
  • What happened before the problem: storm, power cut, long standstill.
  • Whether the outdoor unit makes any sound when you switch on.

With this information, the technician can often bring the right parts on the first visit.

Common mistakes

  • Resetting the breaker repeatedly.
  • Assuming the unit “needs gas” without a diagnosis.
  • Waiting until a heat wave to check the system.
  • Opening the unit’s covers.

Frequently asked questions

Why does the indoor unit run but nothing cools?

The outdoor unit may not be starting, the mode may be wrong, or a protection may be active.

How long should I wait after switching on?

Some units delay compressor start by a few minutes. If nothing happens after several minutes, check further.

Can a dirty filter stop the unit?

It can trigger protections and reduce cooling. Clean filters regularly.

Air conditioning repairs

AcquaKlima Sagl diagnoses and repairs air conditioning systems across Ticino. Learn more about air conditioning or get in touch.

From the blog

Need a quote or a call-out?

Call us or message us on WhatsApp: we reply in Italian, French, German and English.