24/7 on call

A condensing boiler recovers extra heat from the water vapour in its flue gases. When fuel burns, water vapour is formed; in older boilers it escapes up the chimney with the hot gases. A condensing boiler cools the flue gases so much that the vapour condenses and releases its latent heat into the heating water. This works best when the water returning from the radiators is cool. Condensing boilers need a drain for the acidic condensate, sometimes with a neutraliser, and a flue that can handle cool, moist gases. They are more efficient than older boilers, but in Ticino the cantonal renewable energy rule applies when replacing a heat generator.

How condensing works

Burning oil or gas produces water vapour. This vapour carries energy. When it condenses on a cool surface, that energy is released as heat. A condensing boiler has a large heat exchanger where the flue gases are cooled below their dew point. The colder the return water, the more vapour condenses and the more heat is recovered.

Why return temperature matters

Return temperature Effect
Low (underfloor heating, well-balanced radiators) Strong condensation, high efficiency
Moderate Partial condensation
High (unbalanced system, high heating curve) Little condensation; behaves like a conventional boiler

Hydraulic balancing and a well-set heating curve keep return temperatures low.

Requirements

  • Condensate drain: the condensate is acidic and must be drained to the sewer, with neutralisation depending on boiler size and local rules.
  • Flue: cool, moist flue gases require a moisture-resistant liner, often plastic or stainless steel.
  • Fuel: oil condensing boilers use low-sulphur heating oil, standard in Switzerland.
  • Controls: weather-compensated control to run at the lowest necessary temperature.

Oil or gas

Both oil and gas condensing boilers exist. Gas condensing technology is more widespread. Oil condensing boilers require more attention to the condensate and flue. In both cases, the cantonal energy rule in Ticino applies when replacing the heat generator in an existing residential building, as explained in gas boiler replacement.

Limits

A condensing boiler still burns fossil fuel. It reduces consumption compared with an old boiler but does not eliminate CO₂ emissions. It needs servicing and periodic combustion checks. For many houses, a heat pump is a realistic alternative, sometimes after upgrading a few radiators.

Maintenance

  1. Annual service: cleaning, burner adjustment, flue gas measurement.
  2. Check of condensate drain and siphon.
  3. Check and refill of neutraliser if fitted.
  4. Flue inspection.
  5. Preparation for the combustion check.

Condensate pumps

If there is no drain at a lower level near the boiler, a small condensate pump lifts the condensate to a drain. It needs electricity and periodic checks. A failed pump can cause the boiler to shut down or water to overflow, so it should be part of the annual service.

Example: house in Gordola

A homeowner has a new condensing gas boiler but notices the efficiency is lower than expected. The service technician finds a high heating curve and unbalanced radiators, so the return water is too warm for condensing. After balancing and lowering the heating curve, the boiler condenses most of the time, and gas consumption drops.

Efficiency figures explained

Brochures sometimes quote efficiencies above 100% for condensing boilers. This comes from an old convention that measures efficiency against the lower heating value of the fuel, which ignores the heat in the water vapour. When the vapour’s heat is recovered, the figure can exceed 100%. It does not mean the boiler creates energy; it means it recovers heat that older boilers wasted. What matters in practice is how much fuel your home uses over a year.

Heating curve and balancing

To get the most out of a condensing boiler, set the heating curve as low as comfort allows and have the system hydraulically balanced so each radiator gets the right flow. Both lower the return temperature and increase condensation. These measures cost little and often deliver the savings that owners expected when they bought the boiler.

Common mistakes

  • Installing a condensing boiler without adapting the flue.
  • Running high return temperatures.
  • Forgetting the condensate drain and neutraliser.
  • Ignoring the cantonal renewable rule.

Frequently asked questions

How do I know if my boiler is condensing?

It has a condensate drain pipe and usually a plastic or stainless flue. The model plate states the type.

Can the old chimney be reused?

Usually a liner is inserted, because moist flue gases can damage an old chimney.

Is a condensing boiler worth it?

Compared with an old boiler, it saves fuel. Compare it with renewable options before deciding.

Condensing boilers in Ticino

AcquaKlima Sagl installs and services condensing boilers and advises on alternatives across Ticino. Learn more about oil and gas boilers or get in touch.

From the blog

Need a quote or a call-out?

Call us or message us on WhatsApp: we reply in Italian, French, German and English.