24/7 on call

If there is no hot water at home, the cause depends on how your water is heated. With an electric boiler, check the breaker or fuse, the timer or off-peak control, and the thermostat setting. If hot water comes from the central heating, check whether the heating system is running and has no fault, and whether hot water priority or a schedule is set correctly. With a heat pump water heater, check the display for error codes. If only one tap is affected, the problem is likely a mixing valve or a cartridge. Water leaking from the tank, a burning smell or a breaker that trips again are reasons to call a professional immediately.

First: one tap or the whole house?

Situation Likely area
Only one tap or shower cold Mixer, thermostatic cartridge, local valve
Whole house cold Boiler, heating system, power, settings
Hot water runs out quickly Tank size, limescale, faulty element, settings
Lukewarm water only Thermostat, mixing valve, partial fault

Electric boiler

  1. Check the breaker or fuse for the boiler.
  2. Check whether the utility’s off-peak control may have delayed heating.
  3. Check the thermostat setting, if accessible.
  4. Look for water around the tank or a dripping safety valve.

Some boilers have a safety thermostat that cuts off after overheating and must be reset by a professional. The Swiss boiler explained article describes how these tanks work.

Hot water from the central heating

  • Is the heating running? Check for fault lights on the boiler or heat pump.
  • Is the system in summer mode with hot water enabled?
  • Has a schedule or holiday mode been activated?
  • Is there enough fuel (oil level)? If the gas valve is closed and you do not know why, do not reopen it: call the technician. If you smell gas or burning, leave and call for help from outside.
  • Is the system pressure in the normal range?

Heat pump water heaters

These units show error codes on their display. Check that the air inlet and outlet are not blocked and that the room where the unit stands is not too cold. Some units switch to electric backup when the heat pump cannot run. Note the code and contact the installer.

Only one tap is cold

Thermostatic shower mixers have a cartridge that can stick, especially with limescale. Single-lever mixers can fail too. Check whether the isolation valves under the basin are fully open. A plumber can replace the cartridge quickly. Hard water makes these faults more frequent; see hard water in Ticino.

In rented apartments

In many apartment buildings, hot water is produced centrally. If neighbours also have no hot water, the problem is in the central system. Inform the building management, which organises the repair. Do not try to access the central plant room yourself.

When it is urgent

  • Water leaking from the tank or pipes.
  • A breaker that trips again.
  • Burning smell or visible damage.
  • No heating and no hot water in winter.
  • Vulnerable people in the household.

In these cases, contact an emergency service rather than waiting for the next working day.

Prevention

Regular maintenance of the boiler and heating system reduces breakdowns: descaling, anode check, safety valve test and a check of controls. Consider replacing an old boiler before it fails, especially if it is heavily scaled or has started to leak.

Example: house in Losone

On a Monday morning, the whole house has no hot water. The heating also seems cold. The owner checks the display of the oil boiler: it shows a burner fault. A single reset does not help. The service technician finds a clogged oil filter, replaces it and restarts the system. Hot water is back by noon, and an annual maintenance plan is agreed.

Information that speeds up the repair

  • Type of hot water system: electric boiler, central heating, heat pump.
  • Brand and model, from the label on the tank or appliance.
  • Error codes or warning lights.
  • When the problem started and whether anything changed beforehand, such as a power cut or work in the building.
  • Whether the heating works.

With these details, the technician can often diagnose the problem by phone and bring the right parts.

Common mistakes

  • Resetting a burner or breaker repeatedly.
  • Ignoring a dripping safety valve.
  • Turning up the boiler temperature far beyond what is needed.
  • Waiting too long when water is leaking.

Frequently asked questions

Why is there hot water in the evening but not in the morning?

The tank may be too small for morning use or heating times may be poorly set.

Can I reset the safety thermostat myself?

It is better to have a professional check why it tripped.

Is lack of hot water an emergency?

Usually not, unless there is a leak, an electrical fault or vulnerable people in the home.

Fast help for hot water problems

AcquaKlima Sagl repairs boilers and hot water systems and offers an on-call service across Ticino. Learn more about our 24/7 emergency service or get in touch.

From the blog

Need a quote or a call-out?

Call us or message us on WhatsApp: we reply in Italian, French, German and English.