24/7 on call

Pool leak detection starts with a simple question: is the water loss normal evaporation or a real leak? On hot, sunny, windy days a pool can lose a noticeable amount of water through evaporation and splashing. The bucket test gives a useful indication, although wind, rain, splashing and automatic top-ups can distort it: place a bucket filled with pool water on a step in the pool, mark both water levels and compare after a day. If the pool level drops clearly more than the bucket level, you probably have a leak. Typical leak points are the pipework between pool and technical room, the skimmers, the inlets, the lights, the main drain and, for liner pools, small tears.

How much water loss is normal?

There is no single figure, because evaporation depends on water temperature, air temperature, humidity, wind, sun exposure and whether the pool is covered. A heated pool on a windy summer day loses more than an unheated one on a calm, humid day. Splashing, backwashing and topping up for cleaning also take water. That is why comparing against a bucket under the same conditions works better than any rule of thumb.

The bucket test step by step

  1. Fill a bucket with pool water to about the same level as the pool.
  2. Place it on the first or second step so it sits at the same temperature.
  3. Mark the water level inside the bucket and the pool level on the skimmer or a tile.
  4. Switch off automatic top-up systems and do not use the pool.
  5. After 24 hours, compare both drops.
  6. Repeat once with the pump running and once with it off. Make sure the water level never drops below the skimmer mouth while the pump runs, so the pump does not draw air or run dry.

If the pool loses more with the pump running, the leak is likely on the pressure side of the pipework. If it loses more with the pump off, look at the suction side or the pool structure.

Where pool leaks usually hide

Location Typical signs
Skimmer Water level stops dropping at the bottom of the skimmer opening
Lights Level stops dropping at the light; damp in the cable conduit
Inlets and fittings Gaps or cracks around the fittings
Pipework Wet patches in the garden, sinking paving, loss mainly with the pump on
Technical room Drips at the pump, filter, valves or unions
Liner Small tears, often near steps, corners or fittings

Simple checks you can do yourself

  • Watch where the level stops: if it settles at a skimmer or light, that component is suspect.
  • Dye test: with the pump off, release a little test dye near a suspected crack or fitting and see if it is drawn in.
  • Check the technical room: dry everything with a cloth and look for fresh drips.
  • Walk the garden: look for unusually green or soft patches along the pipe route.
  • Check the water meter if the pool is topped up automatically.

Professional leak detection

If the simple checks do not locate the leak, a specialist uses pressure testing of individual pipes, listening equipment and sometimes cameras. Each line is isolated and pressurised to see which one loses pressure. This targeted approach avoids digging up the garden on a guess. Repairs then range from replacing a seal to relining or rerouting a section of pipe.

Why acting early matters

A leak wastes water and treatment chemicals, because fresh water constantly dilutes the sanitiser and changes the balance. Water escaping into the ground can wash out soil under paving or the pool shell and cause settling. In the technical room, drips can damage electrical equipment. Finding the leak early keeps the repair simpler.

Example: pool in Ascona

The owners top up several centimetres a week and assume it is the summer heat. A bucket test shows the pool losing clearly more than the bucket, mainly while the pump runs. The pressure test isolates the return line to one inlet, where a fitting has cracked under the paving. The section is opened, repaired and tested again. Water consumption returns to normal.

Common mistakes

  • Blaming evaporation without testing.
  • Leaving automatic top-up on, which hides the leak.
  • Adding sealant products blindly without knowing where the leak is.
  • Waiting until the end of the season.

Frequently asked questions

Can a pool lose water through the filter?

Yes, through a faulty backwash valve or a drain line left slightly open. Check the waste line in the technical room.

Does a pool cover reduce evaporation?

Yes, a cover significantly reduces evaporation and heat loss when the pool is not in use.

Is leak detection disruptive?

Usually not. Most tests are done from the technical room and the pool itself, without digging.

Leak checks and repairs in Ticino

AcquaKlima Sagl locates and repairs pool leaks and maintains pool equipment across Ticino. Our pool maintenance checklist helps you spot problems early. Learn more about pool maintenance or get in touch.

From the blog

Need a quote or a call-out?

Call us or message us on WhatsApp: we reply in Italian, French, German and English.