24/7 on call

Whether to repair or replace a dripping tap depends on its type, age and condition. Most modern single-lever mixers have a ceramic cartridge; if it drips, replacing the cartridge usually solves the problem. Older two-handle taps with rubber washers can often be fixed with a new washer or seat. If the tap is very old, heavily scaled, corroded, or spare parts are no longer available, a new mixer is often the better choice. Before starting, close the isolation valves under the basin, and identify the brand and model so you buy the right parts.

Find the cause

Symptom Likely cause
Drips from the spout of a single-lever mixer Worn or scaled ceramic cartridge
Drips from a two-handle tap Worn washer or damaged seat
Leaks at the base or handle O-rings or seals
Water under the basin Flexible hoses or connections
Stiff lever and drip Limescale in the cartridge

Repairing a single-lever mixer

  1. Close the isolation valves under the basin; open the tap to release pressure.
  2. Remove the cap and screw of the lever, then the lever.
  3. Unscrew the cover and the cartridge nut.
  4. Take the old cartridge to the shop or note its model.
  5. Fit the new cartridge, reassemble, open the valves and test.

Cartridges vary in size and design. Taking the old one along avoids buying the wrong part.

Repairing a two-handle tap

Older taps with separate hot and cold handles use rubber washers that wear over time. Replacing a washer is a simple job: close the water, remove the handle and headgear, replace the washer and reassemble. If the seat (the surface the washer presses against) is damaged, it may need re-cutting or the headgear may need replacing.

When to replace instead

  • Parts are no longer available.
  • The tap is heavily corroded or the chrome is damaged.
  • Several problems at once: drips, leaks at the base, stiff operation.
  • You want better features: thermostatic control, pull-out spray, water saving.
  • The flexible hoses under the basin are old and should be replaced anyway.

Choosing a new mixer

Look for a well-known brand with available spare parts, a cartridge suited to your water hardness and a flow rate that matches your needs. In kitchens, a pull-out spray is practical. In bathrooms, check the spout height and reach for the basin. Water-saving aerators reduce consumption. For showers, see shower upgrade ideas.

Limescale

Hard water shortens the life of cartridges and aerators. Cleaning aerators regularly and descaling where appropriate helps. If you live in an area with hard water, see hard water in Ticino for wider measures.

Water waste

A tap that drips steadily wastes water every day, and a hot water drip wastes energy too. Fixing it promptly saves money and avoids limescale stains on the basin.

Flexible hoses

The braided hoses connecting the mixer to the isolation valves age over time. A burst hose can cause serious water damage. If they are old, stiff or rusty, replace them during the repair. It is a small cost compared to the risk.

Example: kitchen tap in Minusio

A single-lever kitchen mixer drips and the lever is stiff. The owner closes the valves, removes the cartridge and finds it heavily scaled. A new cartridge of the same model is fitted. The plumber also replaces the old flexible hoses, which show rust at the connections. The tap works smoothly again.

Tools you need

  • Screwdriver set and an Allen key set, since many lever screws use hex heads.
  • An adjustable spanner, with a cloth to protect chrome surfaces.
  • A small container for screws and small parts.
  • Descaler and a soft brush for cleaning parts.
  • Silicone grease suitable for drinking water, for O-rings.

Take photos at each step of dismantling. They make reassembly much easier, especially for mixers with several small parts.

Thermostatic mixers

Thermostatic shower and bath mixers have more complex cartridges than single-lever taps. If they drip or no longer hold the temperature, the thermostatic cartridge or the check valves may be the cause. These parts are model-specific and sensitive to limescale. Repair is possible, but if you are unsure, let a plumber do it, because a wrongly assembled thermostatic mixer can deliver water that is too hot.

Common mistakes

  • Forgetting to close the isolation valves.
  • Buying a cartridge without checking the model.
  • Overtightening and damaging parts.
  • Ignoring old flexible hoses.

Frequently asked questions

Can I repair a tap myself?

Simple cartridge or washer replacements, yes, if you are comfortable with basic tools.

How long does a cartridge last?

It depends on use and water quality; hard water shortens its life.

Should a tenant fix a dripping tap?

Minor cleaning and small maintenance can fall to the tenant under Swiss tenancy law; technical repairs are the landlord’s responsibility, whatever the contract says. If in doubt, inform the landlord.

Tap repairs and replacements

AcquaKlima Sagl repairs and replaces taps and mixers across Ticino. Learn more about plumbing services or get in touch.

From the blog

Need a quote or a call-out?

Call us or message us on WhatsApp: we reply in Italian, French, German and English.