24/7 on call

On every air conditioner energy label, SEER (Seasonal Energy Efficiency Ratio) shows how efficiently the unit cools over a typical cooling season; SCOP (Seasonal Coefficient of Performance) does the same for heating. Both are calculated under standardised conditions defined in European rules, which Switzerland applies for energy labelling. A higher number means less electricity for the same cooling or heating. The energy label also shows an efficiency class, the design load and the annual energy consumption under reference conditions. Use these figures to compare units of similar capacity, but remember that real running costs depend on your home, your climate and how you use the system.

What is on the energy label?

Item Meaning
Efficiency class Quick comparison on a letter scale
SEER Seasonal cooling efficiency
SCOP Seasonal heating efficiency, for a reference climate
Design load (Pdesign) The capacity the figures are based on
Annual energy consumption kWh per year under reference conditions
Sound power Noise of indoor and outdoor units

SEER and EER: the difference

EER is the efficiency at one specific operating point at full load. SEER takes into account that an air conditioner runs most of the time at part load and at varying outdoor temperatures. Inverter units perform particularly well at part load, which SEER reflects. For comparing units, SEER is more meaningful than EER.

SCOP and reference climates

SCOP is calculated for different reference climates: average, warmer and colder. The label shows at least the average climate, sometimes more. The milder climate around Lake Maggiore is closer to the “warmer” profile for some months, while higher valleys are colder. If you plan to use the unit for heating in spring and autumn, compare the SCOP for the climate closest to yours.

How to compare units

  1. Compare only units of similar capacity.
  2. Look at SEER for cooling and SCOP for heating, depending on your use.
  3. Check the sound power levels too.
  4. Consider the refrigerant and its climate impact.
  5. Do not choose a larger unit just because its label looks better.

What really affects running costs

  • Correct sizing: see our air conditioner sizing guide.
  • Set temperature: a moderate set point uses much less energy than a very low one.
  • Shading: closed external shutters during the day reduce the load.
  • Usage hours: cooling only rooms in use.
  • Maintenance: clean filters and coils keep efficiency high.
  • Installation quality: correct refrigerant charge and pipe insulation.

Solar power and air conditioning

Air conditioning demand peaks on sunny afternoons, exactly when solar panels produce the most. With a photovoltaic system, a large share of the cooling electricity can come from your own roof. This improves self-consumption and reduces the effective running costs.

Installation costs versus efficiency

A more efficient unit often costs more to buy. Whether it pays off depends on how many hours you use it. In a bedroom used only on the hottest nights, the difference may be small. In a home office or a holiday rental used intensively, efficiency matters more. The broader cost picture is in air conditioning installation cost.

Example: choosing between two units in Tenero

A couple compares two wall units of the same capacity. One is cheaper with a lower SEER and SCOP; the other is more efficient and slightly quieter. They plan to use the unit for heating in spring and autumn too. The installer explains the label figures and the expected usage. They choose the more efficient model, partly because of the heating use and partly because of the lower night-time noise.

Refrigerants and the label

The energy label does not tell you everything about environmental impact. The refrigerant used in the unit matters too. Some refrigerants have a much higher global warming potential than others, and Swiss rules restrict the use of certain refrigerants in new equipment. Ask the installer which refrigerant is used and why. A unit with a lower-impact refrigerant and good efficiency is the best combination. More information is available from the Federal Office for the Environment.

Reading the product information sheet

Besides the label, each unit has a product information sheet with more detailed data, including capacities at different conditions and sound levels at various fan speeds. Ask for it when comparing models; it gives a fuller picture than the label alone.

Common mistakes

  • Comparing units of different capacities by efficiency class alone.
  • Ignoring SCOP when the unit will also heat.
  • Expecting label consumption to match reality exactly.
  • Forgetting maintenance.

Frequently asked questions

Is a higher efficiency class always worth the extra cost?

Not always. It depends on how much you use the system.

Does the label apply in Switzerland?

Switzerland applies energy labelling for air conditioners in line with European rules.

Why does my unit use more than the label says?

Your conditions differ from the reference: set temperature, shading, sun exposure and usage hours all play a role.

Efficient air conditioning

AcquaKlima Sagl helps you choose efficient units and installs them correctly across Ticino. Learn more about air conditioning or get in touch.

From the blog

Need a quote or a call-out?

Call us or message us on WhatsApp: we reply in Italian, French, German and English.